-40%
24VDC 160W Powerful Micro Brushless Cascade Lift Pump DC55JE-24320S 32m 2000LPH
$ 82
- Description
- Size Guide
Description
PowerfulMicro
Brushless Cascade Lift Pump
DC55JE-24320S 24VDC 32m 2000LPH 160W
It is NEW TWO-stage Cascade Pump Product of our series, with high lift value.
Pump is equiped with DRY-RUN Protection mechanism in default.
Inlet:
1/2” thread(M20) with external diameter of appr. 20 mm
, outlet:
1/2” thread(M20) with external diameter of appr. 20 mm
;
Max static lift: 32 meters;
Max horizontal flow rate: 2000 LPH (~ 33 L/Min).
Typical feature is with quite high lift (output pressure) value, but with relatively low flow rate,
suitable for some micro pressure system.
(P.S.: Certain
parameters, cable length and other specific functions can be specially CUSTOMIZED,
under premise of exact discussion and certain MOQ & lead time.
)
This is a NEW series initiated by our company:
If it is old users, you will know that our older single-stage pump DC50E-24150S model or DC55E-24160S model (with power consumption of appr. 80W and lift value of appr. 15-16m at 24VDC).
As a comparison, this current Two-stage cascade pump DC55JE-24320S model is obviously more powerful.
Main Features
Brushless DC motor, also known as EC motor; Magnetic Driven (
NO DIRECT AC 100-240V POWER CONNECTION, PROHIBITED
);
Small size but strong; Low consumption & High Efficiency;
Long time continuous working with low noise;
Safety - no spark, Explosion - proof; Low noise about 40dB;
Submersible, 100% waterproof; Max Working Temperature: 100 degree;
Wide range of working voltage; Maintenance - free;
Can be used to pump water, oil, other non-corrosive liquids (special liquids are needed to be pre-tested in advance);
Variety Power: DC electric source, Battery or Solar Panel, etc;
Soft Start with Low in-rush current, Especially suitable for Solar SYS who can not provide over-high startup impulse current;
Eco-friendly material design
OEM and ODM are accepted based on MOQ and exact inquiry of customers.
Specifications
Model: DC55JE-24160S Pump (3Phase brushless DC designed pump, TWO-stage cascade design)
Size:
162mmx77mmx112mm
Weight: ~1500g
Material: Engineering Plastics (Eco-friendly)
Inlet:
1/2'' threaded (external diameter appr. 20mm)
Outlet:
1/2'' threaded (external diameter appr. 20mm)
Heat Resistance: -30~100°C
Rated Voltage: DC 24V
Rated Current: 6.7 A at 24VDC
Power Consumption: 160W at 24VDC
Static Head: 32 meters
Flow Rate: 2000L/H
Life Span: Support continuous work in
normal working status, up to 30,000 hrs for nice working environment.
Plug: 4-PIN connector (a bit special)
Cable Length: about 1.5-2 meters
Working: Continuous
Noise: <= 40dB
Water Proof: 100% (note: controlbox part not be placed under water)
Submersible: Yes
Driven: Brushless Magnetic
Self-priming: No
Speed Adjustable: No
Package includes:
1 x All-new Original DC55JE-24320S Micro Brushless DC Water Pump (Two-stage Cascade design)
(No power supply is included:
If power supply is AC/DC power adapter, output capacity of adapter should be 24VDC, 8A ~ 10A.)
P.S.: As we see on pictures, the connector of pump is with 4-PIN connector type, which is a bit special.
If it happens that our users find that it is not to do the cable connection, it will be suggested to directly violently cut off the connector:
two sub-cables inside, typically RED +, BLACK -, connecting with matching 24V DC power supply.
Regarding DC60 series or DC80 series pumps, there are some notes (Not only refering to current pump model listed on this page), As follows.
As micro brushless dc pump, it works via electronic commutation while not brush friction, so there exists no loss caused by brush friction. Pump works with relatively high efficiency.
Pump supports continuous long time work with relatively low noise at normal working environment.land use or submersible installation (Some extra attention needs to be paid to, as mentioned in the final clause) can be both OK, but it cannot be self-priming, just make sure that fluid can actively flow passing through inlet/outlet because pump works via centrifugal force of high-speed rotation of impeller inside (push/throw fluid out). No long-time dry work without fluid, or it may damage the pump.
DC 12V or DC 24V power supply (Depending on rated voltage of pump). No direct AC power powering or over-voltage powering.
Do NOT throw the pump or install it violently, as it could damage the pump body. Do NOT throw the pump directly through the cable, to avoid damage of cable. FIX the pump somewhere at work, to avoid its moving at run, causing little in-flow and dry run, though pump has dry-run protection mechanism designed inside.
If it is AC/DC Power adapter, make sure that it can offer sufficient power to pump. (For example, if it is 24VDC 100W pump, then AC/DC power adapter must have output capacity of 24VDC, >=6A; if it is 12VDC 80W pump, then AC/DC power adapter must have output capacity of 12VDC, 7A or more. Otherwise, it is less powerful to run the pump. Other pumps will be applied with similar mechanism.)
Do not directly throw or pick the pump through its cable, since it could damage the cable, especially at connection point between cable and pump body.
IMPORTANT NOTE:
Control box part (rectangle shape) is NOT recommended to be under water. It’s recommended to be placed off water, especially at long term work. If really have to, it is recommended that some firm waterproof tapes can be closely wrapped on the controlbox part before it is placed under water, to streghten its waterproof class. Just for in case. Sure, it is without issue if control box is just placed under water for short time.
DRY-RUN PROTECTION feature is now equiped in the pump’s design. Pump works at rated voltage: when water flow is gone or in-sufficient, pump will auto access protection mode: run & stop, run & stop, ..., to protect pump’s motor part from being physically damaged from long time extensive friction and heat at continuous dry run; when water flow is back to sufficient status, pump will immediately normally run. This can help avoid that pump can be easily dead when it dry runs for long time. -- It is the NEW feature! (P.S.: Of course, very long time dry run will still need to be avoided by us as users, since pump won't stop but its running sharply slows in this context. )
Shopping
1. Please make sure whether item(s) you want to order is/are the right one(s) you need and we do advise that customer friends pre-contact us about relevant issue if you are not sure, to avoid possible extra waste caused by inappropriate choice.
2. Import duties, taxes and charges are not included in item price or shipping charges and Customs clearance is buyer’s responsibility. Please check with your local Customs authorities before purchase.
(If respected customer doesn't undertake Customs clearance duty, all relevant loss will be customer's duty; when in need, we as responsible vendor will provide all essential documents to help complete Customs clearance, within our ability)
Payment
1. We accept direct order payment on eBay itself.
2. Bulk orders can be accepted. Products are always full in stock, or can be customized for specific requirement after communication
Shipping
1. Your item(s) will be shipped out within 1-2 business days after order payment has been successfully verified on eBay platform.
2. In order for us to have PayPal seller protection, we only ship to address shown in your PayPal payment. We DO NOT ship to any other address requested by email or eBay message.
3. We will pack your item(s) carefully and safely to avoid any damage during transmit; each package has its own tracking No., which will be provided on eBay platform.
4. For ‘Standard Int'l Shipping’, default shipping will be via China Post or Hong kong Post (if package contains battery inside, default shipping will be via Netherlands Post: Hongkong->Netherlands as transit->destination country). For ‘Expedited Int'l Shipping’, default shipping will be via DHL, Fedex, Aramex or EMS, which depend on each specific case. Note that delivery times may vary, especially during peak periods.
Return Policy
1. We have 30 days’ warranty for money back. Refund will be issued after returning item has been received.
2. It’s buyer’s responsibility to contact us about replacement or refund issue within 30 days after defective item has been received; otherwise, we have to reject it. Buyer is responsible for return shipping cost in any cases.
3. All return items must be in original condition, in original boxes, and with all paperwork, parts and accessories; We are not responsible and do not accept any damaged return items. Buyers must pack the return item safely; Please note that your original shipping costs will not be refunded.
About Us
We are always aiming to provide you with nice products and services, as nice as we can. So if you meet with any problem or requirement, please don’t hesitate to contact us!
We are always here, just waiting for you.